AS-Interface模拟模块 VBA-2E-G11-I/U/PT100-V1
来源：未知 日期：2017/12/19 浏览量：次
在AS-Interface 2.1 版本下，最多62个 I/O模块可以被连接到一个AS-Interface 网络中。在最新的 AS-Interface 3.0版本下, 将I/O 容量从124 个输入124 个输出，增加到每网络1000 个I/O。当使用AS-Interface 智能型传感器，这类传感器可以直接被接入网络中, 一个网络最多可以连接62个智能传感器。
AS - Interface现场模块提供了一个强大，紧凑，圆形设计，创新性密封外壳的概念，特别适用于机械装备和过程自动化应用的理想选择。
清洗工序的蒸汽吸尘器，压力冲洗，和较高的机械应力，不影响G11模块的性能。即使在这种恶劣的环境条件下, 也可以快速方便地连接传感器和驱动器的一个AS-Interface。
产品特点：● Function display for bus, internal and external sensor power supply, inputs
● Supply for inputs from AS-Interface or auxiliary voltage
● Degree of protection IP68 / IP69K
● Accuracy ± 0.1 %
● Channel-specific input monitoring
● Inputs for current, voltage or Pt100 temperature sensor
| 产品阐述： | ||
|---|---|---|
|
G11 analog module 2 analog inputs |
||
| 一般特性： | ||
|---|---|---|
| Slave type | Standard slave | |
| AS-Interface specification | V3.0 | |
| Required master specification | ≥ V2.1 | |
| UL File Number | E223772 | |
| 功能安全性参数： | ||
| MTTFd | 190 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| 指示灯/操作键： | ||
| LED AS-i/FAULT |
Status display; multi-colour LED Green: normal operation Red: communication fault Flashing yellow/red: address 0 Flashing green/red: peripheral fault |
|
| LED ANALOG |
status of input signal; LED yellow off: not active on: signal within measurement range flashing: signal outside of measurement range |
|
| LED AUX |
ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
|
| LED INT/EXT |
status display input supply; LED green green: input supply from AS-Interface off: input supply from auxiliary voltage |
|
| 电气特性： | ||
| Auxiliary voltage (output) | 20 ... 30 V DC PELV | |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface | |
| Rated operating current | ≤ 60 mA (without sensors) / max. 200 mA | |
| Protection class | III | |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) | |
| 输入： | ||
| Number/Type |
2 analog inputs Current: 0 ... 20 mA/4 ... 20 mA voltage: 0 ... 10 V Pt100: -200 ... 850 °C |
|
| Supply | from AS-Interface (switch position INT, default settings) or auxiliary voltage UEXT (switch position EXT) | |
| Current loading capacity |
≤ 140 mA from AS-Interface; overload and short-circuit resistant ≤ 600 mA from external auxiliary voltage UAUX , overload and short-circuit protected |
|
| Input resistance |
current input: max. 70 Ω voltage input: 100 kΩ |
|
| Measuring current | for Pt100: approx. 1 mA | |
| Accuracy |
Voltage/current: 0.1% of accumulated value Pt100: 0.1% of indicated temperature [°C] + 0.3 °C |
|
| Resolution |
16 Bit / 1 µA (current input) or 16 bit / 1 mV (voltage input) or 16 Bit / 0.1°C (temperature input) |
|
| Temperature influence |
Voltage/current: 20 ppm/K Pt100: (10 ppm of indicated temperature [°C] + 0.003 °C)/K |
|
| 与标准和规范体系的一致性： | ||
| Directive conformity | ||
| EMC Directive 2004/108/EC | EN 50295:1999 | |
| Standard conformity | ||
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, IEC 62026-2:2008 | |
| Emitted interference | EN 61000-6-4:2007 | |
| Input | EN 61131-2:2007 | |
| Degree of protection | EN 60529:2000 | |
| Fieldbus standard | EN 50295:1999, IEC 62026-2:2008 | |
| 编程指令： | ||
| Profile | S-7.3.D | |
| IO code | 7 | |
| ID code | 3 | |
| ID1 code | F | |
| ID2 code | D | |
| Data bits (function via AS-Interface) | The transfer of the data value is based on AS-Interface Profile 7.3. | |
| Parameter bits (programmable via AS-i) | function | |
| P0 |
50/60 Hz filter P0=1, enabled P0=0, disabled |
|
| P1 |
projecting of the 2nd channel P1=1, channel 2 is projected P1=0, channel 2 is not projected |
|
| P2 |
Indication of the peripheral fault by exceeding measuring range P2=1, peripheral fault is reported P2=0, peripheral fault is not reported |
|
| P3 |
P3=1, normal operating mode P3=0, both channels in current mode and without recognition of wire breakage |
|
| 周围环境： | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 85 % , noncondensing | |
| Climatic conditions | For indoor use only | |
| Altitude | ≤ 2000 m above MSL | |
| Pollution degree | 3 | |
| 机械特性： | ||
| Degree of protection | IP68 / IP69K | |
| Connection |
AS-Interface/UAUX: M12 round connector Inputs: M12 round connector |
|
| Material | ||
| Housing | PBT PC | |
| Mounting screw | Stainless steel 1.4305 / AISI 303 | |
| Mass | 200 g | |
| Tightening torque, housing screws | 1.8 Nm | |
| Tightening torque, cable gland | 0.4 Nm | |
| Mounting | Mounting plate | |
尺寸图
如果您对以上产品有兴趣或有疑问，请联系我们的在线客服或拨打021-39520660，上海锝秉工控专业的采购顾问将为您提供最优的采购咨询服务。
物流运输更安全！ 在上海锝秉工控货品运输的费用从未被加进您所购买产品的售价中。只要您需要，我们就会免费为您提供服务。在运输方式上，上海锝秉工控一般采用快递方式发货，因为快递一般注重产品安全，打包时里面会装有海棉等填充物，这样可以避免运输途中的损坏，同时快递运输时间短，从而也减少客户的等待。
我们一起省钱！ 当您需要订购上海锝秉工控产品时，如我们库存有现货，您需支付全部货款，我们给您发货，如果是期货的，您需先支付30%定金，货到我们公司后您再支付100%的货款，您的及时付款是对我们工作的支持，同时也为我们节省了财务成本，这也是我们能一贯保持优质低价的原因之一。欢迎您的参与，让我们一起省钱吧！
用心服务客户至上！ 在上海锝秉工控购买的产品，可以享有上海锝秉工控强大的技术团队为您提供一对一的技术支持服务!在产品使用过程中，您遇到任何产品安装或是调试的问题，都可以随时联系我们，我们必定尽心尽力为您服务。用心服务，客户至上是我们服务的宗旨！