模拟量输入模块 LB3105A2
来源：未知 日期：2017/11/17 浏览量：次
模块化的远程I/O系统通过总线接口将现场二进制和模拟量的传感器和执行器连接至控制系统的方式传输安全区域或者爆炸危险区域的现场过程数据。模块化的远程I/O系统通过总线接口将现场二进制和模拟量的传感器和执行器连接至控制系统的方式传输安全区域或者爆炸危险区域的现场过程数据。
可以将4 ~20 mA设备连接到远程I/O，例如流量变送器、阀门定位器、压力传感器或者温度变送器。诸如热电偶（TCs）、电阻式温度检测器（RTDs）、机械触点以及声光报警器等设备也可以连接到远程I/O。我们的远程I/O系统能够兼容PROFIBUS DP, MODBUS RTU, MODBUS TCP/IP 和 FOUNDATION fieldbus等网络协议。
LB远程I/O系统能够安装于危险区 Zone2或者Zone 22以及安全区。该系统是模块化的信号处理系统，是现场信号和安全区的控制系统之间的接口界面。LB远程I/O系统通过标准的总线通讯协议（PROFIBUS, Modbus 等），将传统的传感器和现场设备的信号传送给DCS。可插拔的输入和输出模块能够在线热插拔。
I/O模块有一系列单通道和多通道的模块可供选择同时满足本安应用以及增安的现场连接要求。这样的设计简化了工程设计并且满足工厂的需要。
产品特点：● 4-channel
● Inputs Ex ia
● Mounting in Zone 2, Class I/Div.2 or in the safe area
● Power supply for 2-wire transmitters with 4 mA ... 20 mA
● Supply circuit 15 V (20 mA)
● Input from active signals of 4-wire transmitters
● HART communication via field bus or service bus
● Simulation mode for service operations (forcing)
● Line fault detection (LFD): one LED per channel
● Permanently self-monitoring
● Module can be exchanged under voltage
| Slots： | ||
|---|---|---|
| Occupied slots | 2 | |
| Supply： | ||
| Connection | backplane bus | |
| Rated voltage | 12 V DC , only in connection with the power supplies LB9*** | |
| Power dissipation | 1.5 W | |
| Power consumption | 3 W | |
| 内部总线： | ||
| Connection | backplane bus | |
| Interface | manufacturer-specific bus to standard com unit | |
| 模拟输入： | ||
| Number of channels | 4 | |
| Suitable field devices | ||
| Field device | pressure converter | |
| Field device [2] | flow converter | |
| Field device [3] | level converter | |
| Field device [4] | Temperature Converter | |
| Field device interface | ||
| Connection | 2-wire transmitter | |
| Connection [2] | 3-wire transmitter | |
| Connection [3] | 4-wire transmitter | |
| Connection | 2-wire transmitter (HART): Supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14- 3-wire transmitter: Supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16- Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16- 4-wire transmitter (powered externally): Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16- | |
| Transmitter supply voltage | min. 15 V at 20 mA ; 21.5 V at 4 mA | |
| Input resistance | 15 Ω | |
| Conversion time | max. 100 ms | |
| Line fault detection | can be switched on/off for each channel via configuration tool , configurable via configuration tool | |
| Short-circuit | factory setting: > 22 mA configurable between 0 ... 26 mA | |
| Open-circuit | factory setting: < 1 mA configurable between 0 ... 26 mA | |
| HART communication | yes | |
| HART secondary variable | yes | |
| 传递特性： | ||
| Deviation | ||
| After calibration | 0.1 % of the signal range at 20 °C (68 °F) | |
| Resolution | 12 Bit (0 ... 26 mA) | |
| Refresh time | 100 ms | |
| 指示灯/设置： | ||
| LED indicator |
Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) |
|
| 指令符合： | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2006 | |
| 符合： | ||
| Electromagnetic compatibility | NE 21:2007 | |
| Degree of protection | IEC 60529:2000 | |
| 周围环境： | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance |
frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| 机械特性： | ||
| Degree of protection | IP20 when mounted on backplane | |
| Connection |
removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
|
| Mass | approx. 150 g | |
| Dimensions | 32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch) | |
| 在危险区域连接的应用程序数据： | ||
| EU-Type Examination Certificate | BVS 12 ATEX E 024 X | |
| Marking |
 II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC |
|
| Supply | ||
| Voltage | 27 V | |
| Current | 90 mA | |
| Power | 588 mW (linear characteristic) | |
| Input | ||
| Voltage | 0.7 V | |
| Current | 2.78 mA | |
| Power | 2 mW (trapezoid characteristic curve) | |
| Internal capacitance | 242 nF | |
| Internal inductance | 0 mH | |
| Galvanic isolation | ||
| Input/power supply, internal bus | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 2014/34/EU |
EN 60079-0:2009 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 EN 50303:2000 |
|
| 国际认证： | ||
| ATEX approval |
BVS 12 ATEX E 024 X |
|
| UL approval | E106378 | |
| IECEx approval | BVS 12.0055X | |
| Approved for |
Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I |
|
| Marine approval | ||
| Lloyd Register | 15/20021 | |
| Bureau Veritas Marine | 22449/B0 BV | |
电气接线图
如果您对以上产品有兴趣或有疑问，请联系我们的在线客服或拨打021-39520660，上海锝秉工控专业的采购顾问将为您提供最优的采购咨询服务。
物流运输更安全！ 在上海锝秉工控货品运输的费用从未被加进您所购买产品的售价中。只要您需要，我们就会免费为您提供服务。在运输方式上，上海锝秉工控一般采用快递方式发货，因为快递一般注重产品安全，打包时里面会装有海棉等填充物，这样可以避免运输途中的损坏，同时快递运输时间短，从而也减少客户的等待。
我们一起省钱！ 当您需要订购上海锝秉工控产品时，如我们库存有现货，您需支付全部货款，我们给您发货，如果是期货的，您需先支付30%定金，货到我们公司后您再支付100%的货款，您的及时付款是对我们工作的支持，同时也为我们节省了财务成本，这也是我们能一贯保持优质低价的原因之一。欢迎您的参与，让我们一起省钱吧！
用心服务客户至上！ 在上海锝秉工控购买的产品，可以享有上海锝秉工控强大的技术团队为您提供一对一的技术支持服务!在产品使用过程中，您遇到任何产品安装或是调试的问题，都可以随时联系我们，我们必定尽心尽力为您服务。用心服务，客户至上是我们服务的宗旨！
上一篇：模拟量输入模块 LB3104A2
下一篇：RTD转换器 LB5004A