数字量输出模块 FB6210BR
来源：未知 日期：2018/02/01 浏览量：次
模块化的远程I/O系统通过总线接口将现场二进制和模拟量的传感器和执行器连接至控制系统的方式传输安全区域或者爆炸危险区域的现场过程数据。模块化的远程I/O系统通过总线接口将现场二进制和模拟量的传感器和执行器连接至控制系统的方式传输安全区域或者爆炸危险区域的现场过程数据。
可以将4 ~20 mA设备连接到远程I/O，例如流量变送器、阀门定位器、压力传感器或者温度变送器。诸如热电偶（TCs）、电阻式温度检测器（RTDs）、机械触点以及声光报警器等设备也可以连接到远程I/O。远程I/O系统能够兼容PROFIBUS DP, MODBUS RTU, MODBUS TCP/IP 和 FOUNDATION fieldbus等网络协议。
FB远程I/O可安装在危险区Zone1或Zone21区。信号调节模块可以将现场信号转换并传递到安全区的控制系统中。FB远程I/O通过标准总线技术（Profibus，Modbus and several other）将传统传感器和执行机构连接到DCS系统
输入/输出模块在系统中允许带电插拔而无需获得带电操作许可。
多种单通道/多通道I/O模块具有本安型接口和增安型接口，分别连接本安型现场仪表和隔爆型仪表。远程I/O系统可以很容易的满足用户工程的需求。
数字量输出模块带有反馈定位的单通道和用于驱动阀门，LED和声控报警系统的8通道。
产品特点：● 4-channel
● Outputs Ex ia
● Installation in suitable enclosures in Zone 1
● Module can be exchanged under voltage (hot swap)
● Line fault detection (LFD)
● Positive or negative logic selectable
● Simulation mode for service operations (forcing)
● Permanently self-monitoring
● Output with watchdog
| Slots： | ||
|---|---|---|
| Occupied slots | 2 | |
| Supply： | ||
| Connection | backplane bus / 24 V booster via wire ends | |
| Rated voltage | 12 V DC , only in connection with the power supplies FB92** | |
| Input voltage range | 18.5 ... 32 V DC (SELV/PELV) booster voltage | |
| Power consumption |
0.6 W at power supply 5 W if 24 V booster voltage |
|
| 内部总线： | ||
| Connection | backplane bus | |
| Interface | manufacturer-specific bus to standard com unit | |
| 数字输出： | ||
| Number of channels | 4 | |
| Suitable field devices | ||
| Field device | Solenoid Valve | |
| Field device [2] | audible alarm | |
| Field device [3] | visual alarm | |
| Connection | channel I: 9+, 10-; channel II: 11+, 12-; channel III: 13+, 14-; channel IV: 15+, 16- | |
| Current limit | 37 mA | |
| Internal resistor | max. 370 Ω | |
| Open loop voltage | 24.5 V | |
| Line fault detection | can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms) | |
| Short-circuit | < 100 Ω | |
| Open-circuit | > 15 kΩ | |
| Response time | 10 ms (depending on bus cycle time) | |
| Watchdog | within 0.5 s the device goes in safe state, e.g. after loss of communication | |
| Reaction time | 10 s | |
| 指示灯/设置： | ||
| LED indicator |
LED green: supply LED red: line fault , red flashing: communication error |
|
| 指令符合： | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1 | |
| 符合： | ||
| Electromagnetic compatibility | NE 21 | |
| Degree of protection | IEC 60529 | |
| 周围环境： | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 95 % non-condensing | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance |
frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| 机械特性： | ||
| Degree of protection | IP20 (module) , a separate housing is required acc. to the system description | |
| Connection |
removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
|
| Mass | approx. 750 g | |
| Dimensions | 57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch) | |
| 与危险区域有关的应用数据： | ||
| EU-Type Examination Certificate | PTB 97 ATEX 1074 U | |
| Marking |
 II 2(1) G Ex d [ia Ga] IIC Gb II (1) D [Ex ia Da] IIIC |
|
| Output | ||
| Voltage | 27.8 V | |
| Current | 90.4 mA | |
| Power | 629 mW | |
| Internal capacitance | 2.5 nF | |
| Internal inductance | 0 mH | |
| Galvanic isolation | ||
| Output/power supply, internal bus | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 2014/34/EU |
EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006 |
|
| 国际认证： | ||
| ATEX approval | PTB 97 ATEX 1075 ; PTB 97 ATEX 1074 U | |
| EAC approval | Russia: RU C-IT.MIII06.B.00129 | |
| Marine approval | ||
| Lloyd Register | 15/20021 | |
| DNV GL Marine | TAA0000034 | |
| American Bureau of Shipping | T1450280/UN | |
| Bureau Veritas Marine | 22449/B0 BV | |
电气接线图
如果您对以上产品有兴趣或有疑问，请联系我们的在线客服或拨打021-39520660，上海锝秉工控专业的采购顾问将为您提供最优的采购咨询服务。
物流运输更安全！ 在上海锝秉工控货品运输的费用从未被加进您所购买产品的售价中。只要您需要，我们就会免费为您提供服务。在运输方式上，上海锝秉工控一般采用快递方式发货，因为快递一般注重产品安全，打包时里面会装有海棉等填充物，这样可以避免运输途中的损坏，同时快递运输时间短，从而也减少客户的等待。
我们一起省钱！ 当您需要订购上海锝秉工控产品时，如我们库存有现货，您需支付全部货款，我们给您发货，如果是期货的，您需先支付30%定金，货到我们公司后您再支付100%的货款，您的及时付款是对我们工作的支持，同时也为我们节省了财务成本，这也是我们能一贯保持优质低价的原因之一。欢迎您的参与，让我们一起省钱吧！
用心服务客户至上！ 在上海锝秉工控购买的产品，可以享有上海锝秉工控强大的技术团队为您提供一对一的技术支持服务!在产品使用过程中，您遇到任何产品安装或是调试的问题，都可以随时联系我们，我们必定尽心尽力为您服务。用心服务，客户至上是我们服务的宗旨！
上一篇：数字量输出模块 FB6210B
下一篇：数字量输出模块 FB6210ER