开关放大器 S1SD-1FI-1R
来源：未知 日期：2017/06/19 浏览量：次
对于大多数的控制系统而言，常常需要将输入信号转换为系统可接受的信号模式。那么信号调节器的功能就是将各种现场信号，例如热电偶，热电阻转换为多种标准的仪表信号(1…5V, 4…20 mA, 等.).
SC系统信号调理是专为通用应用程序，并确保绝对可靠的进程通信。高品质的隔离，扩展的温度范围，和一个非常紧凑的住房设计信号调理线的特点。
SC系统提供了模拟和数字测量信号的强大模块-从隔离放大器的高功能温度转换器开关放大器。配套配件启用方便快捷的电源，安装和配置信号调理器。
产品特点：● 1-channel signal conditioner
● 24 V DC supply
● Input for 2- or 3-wire sensors
● Input frequency 10 mHz ... 50 kHz
● Relay contact output
● Start-up override and restart inhibit
● Configurable by DIP switches and software
● Connection via screw terminals
| 一般特性： | ||
|---|---|---|
| Signal type | Digital Input | |
| Supply： | ||
| Connection | Power Bus or terminals 1-, 2+ | |
| Rated voltage | 16.8 ... 31.2 V DC | |
| Power dissipation | 0.6 W | |
| Power consumption | 1.1 W | |
| 输入： | ||
| NAMUR sensor | ||
| Type | 2-wire | |
| Connection | terminals 5+, 6 | |
| Signal | acc. to EN 60947-5-6 (NAMUR) | |
| Sensor supply | 8 V | |
| Open-circuit | < 0.1 mA | |
| Switching point | 1.2 ... 2.1 mA | |
| Short-circuit | > 6 mA | |
| Input impedance | 1 kΩ | |
| Mechanical contact | ||
| Type | 2-wire | |
| Connection | terminals 5+, 6 | |
| Sensor supply | 15 V | |
| External supply | 16.8 ... 31.2 V DC | |
| Switching point | 8 ... 10 V / 1.2 ... 2.1 mA | |
| Frequency | 0 ... 50 Hz , debounce filter | |
| Input impedance | 4 kΩ | |
| SN sensor | ||
| Type | 2-wire | |
| Connection | terminals 5+, 6 | |
| Sensor supply | 8 V | |
| Open-circuit | < 0.1 mA | |
| Switching point | 1.2 ... 2.1 mA | |
| Short-circuit | > 6 mA | |
| Input impedance | 1 kΩ | |
| 2-wire DC sensor | ||
| Type | 2-wire | |
| Connection | terminals 5+, 6 | |
| Signal | acc. to EN 60947-5-2 | |
| Sensor supply | 16 V / 25 mA , short-circuit protected | |
| External supply | 16.8 ... 31.2 V DC | |
| Switching point | 4 ... 6 V | |
| Input impedance | 1 kΩ | |
| S0 sensor | ||
| Type | 2-wire | |
| Connection | terminals 5+, 6 | |
| Signal | acc. to EN 62053-31 , Type B | |
| Sensor supply | 15 V | |
| Switching point | 0.15 ... 2 mA | |
| Input impedance | 4 kΩ | |
| NPN sensor | ||
| Type | 3-wire | |
| Connection | terminals 5+, 6, 7- | |
| Signal | acc. to EN 60947-5-2 | |
| Sensor supply | 16 V / 25 mA , short-circuit protected | |
| External supply | 16.8 ... 31.2 V DC | |
| Switching point | 3 ... 5 V | |
| Input impedance | 4 kΩ | |
| PNP sensor | ||
| Type | 3-wire | |
| Connection | terminals 5+, 6, 7- | |
| Signal | acc. to EN 60947-5-2 | |
| Sensor supply | 16 V / 25 mA , short-circuit protected | |
| External supply | 16.8 ... 31.2 V DC | |
| Switching point | 8 ... 10 V | |
| Input impedance | 4 kΩ | |
| AC source | ||
| Connection | terminals 6, 7- | |
| Signal | max. ± 30 V | |
| Switching point | 150 ... 400 mV | |
| Input impedance | 4 kΩ | |
| Function input | ||
| Connection | terminal 8 | |
| Open loop voltage | 7.5 V | |
| Input impedance | approx. 50 kΩ | |
| Function 1 | activation start-up override | |
| Switching point | < 3 V , edge triggered | |
| Adjustment range | 1 ... 6500 s | |
| Function 2 | reset restart inhibit | |
| Switching point | > 12 V , edge triggered | |
| 输出： | ||
| Connection | terminals 3, 4: | |
| Output | signal, relay | |
| Contact loading | 253 V AC/2 A/cos φ > 0.7; 126.5 V AC/4 A/cos φ > 0.7; 30 V DC/2 A resistive load | |
| Minimum switch current | 2 mA / 24 V DC | |
| Energized/De-energized delay | ≤ 20 ms / ≤ 20 ms | |
| Mechanical life | 107 switching cycles | |
| 传递特性： | ||
| Measuring time | ≤ 100 ms | |
| Deviation | 0.1 % of measured value | |
| Influence of ambient temperature | < 100 ppm/K of the measured value | |
| Frequency range | 0.01 ... 50000 Hz | |
| 指令符合： | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
| Low voltage | ||
| Directive 2014/35/EU | EN 61010-1:2010 | |
| 符合： | ||
| Degree of protection | IEC 60529:2001 | |
| 周围环境： | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| 机械特性： | ||
| Connection type | screw terminals | |
| Core cross-section | 0.5 ... 2.5 mm2 , 20 ... 14 AWG | |
| Degree of protection | IP20 | |
| Mass | approx. 60 g | |
| Dimensions | 6.2 x 97 x 107 mm (0.24 x 3.82 x 4.21 inch) , housing type S1 | |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 | |
| 附件： | ||
| Optional accessories |
power feed module S1SD-2PF adapter with USB interface S-ADP-USB Power Bus POWERBUS-SETL5.*** Power Bus POWERBUS-SETH5.*** cover for DIN mounting rail POWERBUS-COV.250 end cap POWERBUS-CAP splitter VAZ-CHAIN-BU/BN70MM/1,0-25 |
|
如果您对以上产品有兴趣或有疑问，请联系我们的在线客服或拨打021-39520660，上海锝秉工控专业的采购顾问将为您提供最优的采购咨询服务。
物流运输更安全！ 在上海锝秉工控货品运输的费用从未被加进您所购买产品的售价中。只要您需要，我们就会免费为您提供服务。在运输方式上，上海锝秉工控一般采用快递方式发货，因为快递一般注重产品安全，打包时里面会装有海棉等填充物，这样可以避免运输途中的损坏，同时快递运输时间短，从而也减少客户的等待。
我们一起省钱！ 当您需要订购上海锝秉工控产品时，如我们库存有现货，您需支付全部货款，我们给您发货，如果是期货的，您需先支付30%定金，货到我们公司后您再支付100%的货款，您的及时付款是对我们工作的支持，同时也为我们节省了财务成本，这也是我们能一贯保持优质低价的原因之一。欢迎您的参与，让我们一起省钱吧！
用心服务客户至上！ 在上海锝秉工控购买的产品，可以享有上海锝秉工控强大的技术团队为您提供一对一的技术支持服务!在产品使用过程中，您遇到任何产品安装或是调试的问题，都可以随时联系我们，我们必定尽心尽力为您服务。用心服务，客户至上是我们服务的宗旨！
上一篇：开关放大器 S1SD-1DI-1R
下一篇：智能变送器 S1SD-1AI-1C.H